Estimate materials for epoxy, polyaspartic, polyurea, and urethane flooring systems with our free contractor calculator. Quickly calculate primers, base coats, decorative flake, quartz, topcoats, and approximate material costs for your next concrete coating project.

Learn the difference between concrete control joints and expansion joints, how they affect epoxy and industrial flooring installations, and how contractors should approach joint preparation and filling.

The cheapest gallon is often not the cheapest job. Learn how volume solids, dry film thickness and realistic material loss determine coating cost per square foot, with a three-product comparison and pre-bid checklist for Houston steel and floor coating projects.

Why does concrete resurfacing crack, curl or come loose? Learn how to spot poor preparation, covered joints and weak concrete, then decide whether to patch isolated damage, remove a failed overlay or address the slab beneath it.

Epoxy mastic or urethane—or both? Compare Rust-Oleum 9100 and 9800 for rusty steel, with practical guidance on surface preparation, primer requirements, film thickness, recoat windows and Gulf Coast dew point checks.

Can you document the coating thickness your project requires? Learn how mils, WFT, DFT, coverage rates, and inspection tools work together—and what contractors should record before, during, and after installation.

A successful concrete overlay starts before the first bag is mixed. Learn seven checks contractors should make before resurfacing, including slab condition, repairs, bonding requirements, weather, and sealer selection.

Better traction starts with the right additive. Learn how to choose slip-resistant additives for concrete coatings and acrylic-sealed overlays, avoid compatibility mistakes, and match surface texture to your customer’s needs.

Urethane slurry, epoxy mortar, quartz or solid color—which industrial flooring system fits the facility? Compare these resinous flooring systems and learn what contractors should evaluate before selecting a system for warehouses, commercial kitchens, manufacturing facilities and other demanding environments.

The success of an industrial flooring system starts with proper concrete surface preparation. Learn why selecting the correct Concrete Surface Profile (CSP) is essential for coating adhesion, consistent application, and long-term floor performance.

Concrete overlays give contractors a practical way to resurface worn, discolored, or outdated concrete without immediately removing and replacing the entire slab. However, choosing the right concrete overlay requires more than selecting a color or decorative pattern. A patio, pool deck, walkway, and driveway are exposed to different levels of traffic, moisture, heat, and wear. The overlay system must match the environment, the condition of the existing concrete, and the finis

An epoxy flooring system is only as reliable as the concrete beneath it. Even when a slab appears clean and dry, moisture may still be moving through the concrete. If that moisture is not identified before installation, it can cause blistering, bubbling, discoloration, loss of adhesion, and complete coating failure. For concrete coating contractors, moisture testing should be part of the pre-installation process—not something considered only after a floor fails. This guide ex

Metal surface preparation is one of the most important steps in any industrial metal coating project. Even a high-performance coating can fail when it is applied over loose rust, mill scale, grease, soluble salts, trapped moisture, preparation dust, or an unstable existing finish. The completed surface may look acceptable at first, but adhesion problems can appear after exposure to rain, humidity, chemicals, abrasion, or temperature changes. For contractors coating structural

A warehouse floor is more than a finished concrete surface. It supports forklifts, pallet jacks, storage racks, loading operations, employees, equipment, and the continuous movement of materials throughout the facility. When the wrong flooring system is installed, the results can include: Premature wear Concrete dusting Peeling or delamination Tire marks and scratches Chemical staining Slippery work areas Damaged traffic markings Frequent repairs and operational downtime The

Choosing the right concrete repair product is one of the most important steps in preparing a slab for an epoxy, polyaspartic, polyurea, overlay, sealer, or industrial flooring system. Even a high-performance coating system can fail when it is installed over loose concrete, contaminated cracks, deep spalls, weak repairs, or improperly prepared patching material. The challenge is that not every repair requires the same solution. A small surface pit does not need the same materi

Selecting the right topcoat is one of the most important decisions when building a high-performance resinous flooring system. While both Citadel ET-80 and Citadel RG-80X are polyaspartic topcoats designed to protect decorative and industrial concrete floors, they each offer unique advantages depending on the project requirements. Whether you're installing a decorative flake floor, a quartz broadcast system, or a commercial concrete coating, understanding the differences betwe

If your epoxy floor is peeling or failing, recoating won’t fix the problem. Discover the real causes of coating failure and the proper steps to remove, prep, and rebuild a floor that’s built to last.

Most epoxy floors don’t fail because of bad product—they fail before the coating even starts. Proper concrete grinding is what creates the bond, prevents peeling, and ensures long-term performance. Learn why skipping this step leads to costly failures and how to prep the right way.

A professionally coated concrete floor is designed to protect the surface, improve appearance, and make everyday cleaning easier. Whether the system was installed in a garage, shop, warehouse, showroom, patio, or commercial space, proper maintenance plays a big role in how the finished floor looks and performs over time. Many homeowners and property owners think once a floor is coated, it no longer needs care. While coated floors are much easier to maintain than bare concrete

Concrete coating contractors are already comfortable with surface prep, coatings, mix ratios, jobsite conditions, and customer expectations. So when a homeowner or commercial client points to a worn-out metal gate, handrail, dumpster enclosure, pole barn, equipment frame, awning, or metal building and asks, “Can you coat this too?” — the answer does not always have to be no. Metal coatings can be a strong add-on service for contractors who already work with epoxy, urethane, a